90 Degree Corner LED Cabinet vs. Standard Cabinet: Which Fits Retail?
A corner LED cabinet is the right choice when a retail display must wrap a visible 90° shopfront return, column or feature wall without a wide unlit band at the vertex. The correct solution depends on the cabinet series: the source documents 45°-trimmed or factory 45°-cut cabinets for UR Pro and RK Pro, 90° splicing designs for RK, IW, TSL and AM, and a 45° frame cut with a corner connecting piece for AS. These methods are not interchangeable. Confirm the exact corner part number, orientation, trim profile and drawing with the factory before ordering.
Short answer: A 90 degree corner LED cabinet is a cabinet whose side is trimmed, cut or spliced so two faces can be joined at a true right angle with no unlit band at the vertex. In Uniview LED(优景观复) documentation, the corner condition is solved three ways: a 45°-trimmed cabinet on UR Pro (the indoor and outdoor manuals specify only the 45°-trimmed 500 × 500 mm cabinets, locked with the 45° quick locks) and a factory 45° cut on RK Pro; a 90° splicing design on RK, IW, TSL and AM; and a 45° frame cut plus corner connecting piece on AS. Corner cabinet part numbers and project-specific corner drawings still need to be confirmed per series and per project.
Corner LED Cabinet Design: Why a 90° Corner Is a Cabinet Decision
A corner LED screen is produced by the shape of the cabinet’s side, not by a corner trim piece. Two cabinets can meet at 90° in only two ways: butt-jointed, or mitered.
In a butt joint, one face runs straight through the corner and the second face starts where the first one ends. The second face’s cabinet body needs room behind the first face’s plane, so either the corner region is left empty or one face is stepped back. Either way the shopper sees an unlit vertical band, a metal return, or a visible break in the plane at exactly the point where the eye is most likely to land.
In a mitered joint, each cabinet’s side is cut at 45° so the joint plane bisects the corner. The two front faces meet on a single vertical line at the vertex, and both faces keep their full module width up to that line. This is the geometry the UR Pro manual describes when it specifies 45°-trimmed 500 × 500 mm cabinets. Two 45° faces joined together form a 90° corner as a direct geometric consequence of the trim angle.
What the Uniview LED(优景观复) Documentation Specifies, Series by Series
The table below separates what each document states from what still needs a project confirmation. The pack documents 45°-trimmed or factory 45°-cut cabinets on UR Pro and RK Pro, 90° right-angle splicing on RK, IW, TSL and AM, and a 90° corner screen with a 45° frame cut plus a corner connecting piece on AS.
| Series | Corner option documented in this source pack | Documented cabinet geometry | What must be confirmed before order |
|---|---|---|---|
| UR Pro | Yes. UR Pro Indoor and Outdoor User Manuals (V1.0): “Only the 45 degree trimmed cabinets of 500*500mm can be assembled into a corner screen.” A “connecting piece” is listed in the accessory kit for corner screen installation. | Indoor 500 × 1000 × 83 mm and 500 × 500 × 83 mm; outdoor manual lists 500 × 500 × 87.5 mm and 500 × 1000 × 87.5 mm. Indoor pitches in the 500 × 1000 sheet: 1.953 mm (GOB), 2.604 mm, 2.976 mm. | Convex vs concave orientation; edge trim profile width; corner cabinet as a separate order line; corner cabinet weight (not published). |
| AS | Yes. AS Series user manual section 3, “Corner Screen Installation (90°)”: the frame of AS series is cut by 45° on the left or right side, used together with a corner connecting piece. The AS brochure describes the series as flat-, curved- or corner-capable; the AS configuration sheet (V.2023512) documents a curved-angle option of ±6°, ±3° and 0°. | 500 × 500 × 80 mm, 7.6 kg per cabinet, IP30/IP30, screen flatness ≤1 mm. | Front-installation module removal first, as stated in the manual; corner cabinet part number / drawing not published. |
| RK / RK Pro | Yes. RK Pro brochure (2026-03-26): “Cabinets can be cut to 45° angles for seamless corner fitting.” RK brochure (2026-05-22): “It can realize horizontal and right angle splicing and installation … Right Angle Splicing 90°.” | 960 × 960 mm cabinets; depths 87.1 / 87.5 / 88.1 mm (RK P6.6 / P8 / P10) and 91.51 / 93.4 mm (RK Pro P6.6 / P10). | Corner cabinet part number and corner detail drawing not published; confirm the RK Pro factory 45° cut order line and the RK right-angle splicing joint and edge trim. |
| IW / TSL / AM | Yes. IW brochure (2026-05-11): “90°splicing design enables vertical splicing”; IW also documents 0°, ±3°, ±6° arc. TSL brochure (2026-05-12): “90 ° Right angle spliced.” AM brochure (2025-08-08): “90° External right-angle” with curve splicing adjustable at ±15°. | Refer to the current series specification sheets. | Corner cabinet part number / drawing not published; confirm whether the project uses the 90° right-angle configuration, the IW 0° / ±3° / ±6° arc option, or the AM ±15° curve adjustment. |
Reading this table correctly: where a detail such as a corner cabinet part number or corner drawing is not published in the pack, that does not mean the corner cannot be engineered. Quote it as a project-specific item and confirm it with the factory rather than assuming it from the series name.
Documented UR Pro corner assembly sequence
- Align the two trimmed frames so the 45° faces sit square to each other.
- Pass the installed left and right 45° quick locks through the corresponding lock holes, left to right.
- Turn the handle clockwise until the left and right cabinets are locked tightly.
- Lock the quick lock at the bottom of the frame using the same method, then check flatness from the front.
Source: URPro Series User Manual (Indoor V1.0 and Outdoor V1.0), section 3.3 “Corner installation”.
Cabinet geometry: the cabinet depth becomes the width of the dark band
At a butt-jointed 90° corner, the cabinet depth turns into an unlit band. The number that matters in the quotation is not the pixel pitch — it is the depth of the cabinet on the return face.
On a UR Pro 500 × 500 mm indoor cabinet the documented depth is 83 mm. If the two faces are butted rather than mitered, one face must give up at least that 83 mm before the two cabinet bodies can coexist at the corner. That is 16.6% of a 500 mm cabinet column (editorial calculation: 83 ÷ 500), delivered as a dead vertical stripe with no pixels — and it lands precisely where a shopper’s eye is drawn on a shopfront return.
| Documented cabinet depth | Series and source | Minimum band at a butt-jointed corner |
|---|---|---|
| 80 mm | AS 500 × 500 × 80 mm (AS configuration sheet V.2023512) | ≥80 mm on one face |
| 83 mm | UR Pro indoor 500 × 500 × 83 mm (UR Pro Indoor User Manual V1.0) | ≥83 mm on one face |
| 87.7 mm | UR Pro outdoor 500 × 1000 × 87.7 mm (UR Pro configuration sheet V.202608) | ≥87.7 mm on one face |
| 87.1 / 87.5 / 88.1 mm | RK P6.6 / P8 / P10 (RK specification sheet V.202604) | ≥87.1 / 87.5 / 88.1 mm, depending on pitch |
| 91.51 / 93.4 mm | RK Pro P6.6 / P10 (RK Pro configuration sheet V.202608) | ≥91.51 / 93.4 mm, depending on pitch |
Specification check before publication: the supplied source pack gives the UR Pro outdoor cabinet depth as 87.5 mm in the user-manual summary and 87.7 mm in the configuration-sheet entry used in the table above. Keep the value tied to the exact model and document revision in the final quotation; do not treat the two figures as interchangeable.
The 45° trim removes this problem at the source. The chamfer runs backward from the vertex behind the front face, so the LED surface of each cabinet runs all the way to the corner line and the lit width lost at the vertex is nominally zero. The real figure depends on the edge trim profile and any masking strip, and the UR Pro manual does not publish a trim profile width — treat that dimension as a project confirmation item, not a design assumption.
Angle limitation: a 45° trim is a 90° solution and nothing else. A 135° shallow return, a 60° chamfer or a curved-to-flat transition needs a different side cut or a curved option such as the AS ±6° / ±3° / 0° configuration. Do not specify a 45°-trimmed cabinet for a non-90° corner.
Worked example: a 1,500 × 2,000 mm corner in a store
Take a convex 90° corner wrapping a structural column, two faces each 1,500 mm wide and 2,000 mm high, built from UR Pro P2.604 mm indoor cabinets. Both dimensions land exactly on the 500 mm module grid, which is the first thing to check on any corner project.
| Item | Option A — all 500 × 500 mm cabinets | Option B — 500 × 1000 mm flat faces, 500 × 500 mm corner columns |
|---|---|---|
| Corner cabinets (45° trimmed) | 4 rows × 2 faces = 8 | 4 per face × 2 faces = 8 |
| Standard cabinets | 16 × 500 × 500 mm | 8 × 500 × 1000 mm |
| Total cabinets | 24 | 16 |
| Horizontal seams per column | 3 | 1 |
| Resolution per face at P2.604 | 576 × 768 px | 576 × 768 px |
| Lit area (both faces) | 6.0 m² | 6.0 m² |
| Max / average power at 620 / 210 W/m² | 3.72 kW / 1.26 kW | 3.72 kW / 1.26 kW |
Resolution, area and power are editorial calculations from documented values: 2.604 mm pitch gives 192 px per 500 mm; 620 / 210 W/m² is the UR Pro P2.604 maximum / average power consumption from the UR Pro configuration sheet V.202608.
Option B is usually the better buy. It cuts the cabinet count from 24 to 16 and removes two horizontal seams from every column, at the cost of ordering two cabinet heights for one job. Option A is the right choice only when the whole facing must be 500 mm modular for a repeating multi-site pattern.
| Series | Documented right-angle method | Angle range stated | Source |
|---|---|---|---|
| UR Pro | 45° corner cabinet; small cabinet supports 90° splicing | 45° trim; 90° joint | UR Pro brochure 2025-12-01 |
| RK Pro | Cabinets cut to 45° for seamless corner fitting | 45° cut | RK Pro brochure 2026-03-26 |
| RK | Plane splicing and right-angle splicing | Right angle | RK brochure 2026-05-22 |
| IW | Dual-purpose 90° splicing; concave and convex arc | 0°, ±3°, ±6° arc | IW brochure 2026-05-11 |
| TSL | 90° right-angle spliced | 90° | TSL brochure 2026-05-12 |
| AM | 90° external right-angle; curve splicing | Curve adjustable at ±15° | AM brochure 2025-08-08 |
| AS | Corner screen installation with corner connecting piece | 90° | AS Series user manual |
| UR | Right-angle and convex-curve configurations | Right angle | UR brochure 2025-11-27 |
Every row is a direct statement from the named document. The method differs by series; the angle range is what a store rollout should standardise on.
Corner pixel alignment: six rules that decide whether the seam reads clean
Pixel alignment at a 90° corner is not about matching pixels across the vertex — there is no continuous pixel at the vertex. It is about making the diagonal termination of each face look deliberate rather than ragged.
- Use one pitch on both faces. A UR Pro 500 mm edge carries 256 px at P1.953, 192 px at P2.604 and 168 px at P2.976. Changing pitch at the corner changes pixel density at the closest, most scrutinized point of the installation.
- Design a vertical break line into the content. The 45° cut means the last pixel column of each face ends on the diagonal. A single continuous image mapped across the miter will visibly fold. Create the creative as two panels meeting at a deliberate line, or pre-distort the artwork.
- Map each face as its own rectangle in the processor. Give face A and face B separate rectangular outputs from the receiving card or video processor. A single canvas wrapped around the corner cannot be pixel-accurate at the vertex.
- Keep calibration and batch consistent. Both faces should come from one calibration run and, where possible, the same LED batch. A corner is the worst place to discover a color temperature shift between cabinets — the UR Pro series is specified at 5500–9500 K.
- Check off-axis brightness at 45°. A viewer standing on the corner bisector sees both faces roughly 45° off-axis. UR Pro indoor is documented at a 160°/160° viewing angle and UR Pro outdoor at 140°/140°, but the sheets do not publish luminance at 45° off-axis — request the measured curve if the corner faces the main sightline.
- Protect the seam mechanically. Specify the edge trim or masking profile, a matte black joint fill, and a service procedure that does not require levering against an exposed module edge.
| UR Pro pitch | Pixels per 500 mm edge | Pixels on a 500 × 500 mm corner cabinet |
|---|---|---|
| 1.953 mm (GOB) | 256 | 256 × 256 |
| 2.604 mm | 192 | 192 × 192 |
| 2.976 mm | 168 | 168 × 168 |
Derived from the documented 500 × 1000 mm panel resolutions in the UR Pro configuration sheet V.202608 (256 × 512, 192 × 384, 168 × 336). The 500 × 500 mm corner cabinet resolution is an editorial derivation, not a published figure.
Retail Viewing Distance and Corner Sightlines
A clean corner seam is only one part of a retail display design. Screen size, content detail and the closest and farthest shopper positions should also be checked against the intended viewing task. AVIXA’s V202.01:2026 standard for display image size in audiovisual systems defines display image size and relative viewing positions for basic and analytical decision-making. It is a system-level viewing reference, not a cabinet-corner construction standard; use it alongside the series-specific cabinet drawings.
When a corner cabinet beats a standard cabinet
A corner cabinet wins when the vertex is inside the shopper’s field of view. It loses when the vertex is structurally hidden or viewed from far enough away that a band of 80–95 mm is not legible.
| Project condition | Better choice | Reason |
|---|---|---|
| Corner wraps a mall column on the main walking path | 45°-trimmed corner cabinet | No dead band; the corner reads as one continuous surface. |
| Corner is a shopfront return seen from 1–3 m | 45°-trimmed corner cabinet | At this distance a butt-joint band is unmistakable. |
| Content is a logo, gradient or full-bleed brand color across the corner | 45°-trimmed corner cabinet | A dark stripe breaks brand color; a mitered seam does not. |
| Corner is behind a fixed obstruction, plant room or service door | Standard cabinet, butt joint | The band is never seen; spend the budget on pitch instead. |
| Large-format outdoor screen viewed at 10 m or beyond | Standard cabinet, butt joint | At that distance an 87–93 mm band is a fraction of a degree of view; check the documented minimum viewing distance for the pitch (6.7 m for RK6.6, 8 m for RK8.0, 10 m for RK10.0). |
| Corner angle is not exactly 90° | Neither — request a custom cut or a curved option | A 45° trim only produces a 90° corner. |
| Rollout across many identical stores | 45°-trimmed corner cabinet | A factory corner (45° cut or 90° splicing) is repeatable store to store; a site-fabricated corner post is not. |
| Rear access is blocked at the corner | Either, if front service is specified | UR Pro documents front and rear module and PSU maintenance on both indoor and outdoor sheets. |
Specification and procurement checklist
- Corner type and angle: convex or concave, and exactly 90° or not. The UR Pro manual documents the 45° joint but does not distinguish convex from concave, so confirm orientation with the factory.
- Grid check: face widths and heights in whole 500 mm modules. A 1,460 mm face forces a cut cabinet at the corner — the worst place for one.
- Corner cabinet quantity: one corner cabinet per 500 mm row per face. A 3 m tall corner needs 6 rows × 2 faces = 12 corner cabinets.
- Separate order line: corner cabinets carry their own part number and are not interchangeable with standard cabinets. Order spares as corner cabinets.
- Trim profile: width, color and material of the edge trim at the vertex, plus the joint fill specification.
- IP rating for the environment: UR Pro indoor is documented at IP30/IP30 and is not a wet-area product; UR Pro outdoor P2.9/P3.9 is documented at IP65/IP54.
- Interpret IP ratings against the correct standard: when selecting indoor or outdoor cabinet variants, verify the stated front and rear ratings against the exact product sheet and project environment. IEC 60529 defines the IP Code for enclosure protection; it does not replace confirmation of the rating declared for the specific cabinet.
- Power and data at the corner: the corner cabinet still needs power and data; it does not shorten the chain. Use 620/210 W/m² (UR Pro P2.6 indoor) or 700/235 W/m² (UR Pro P2.9/P3.9 outdoor) for load planning.
- Hanging limit: the UR Pro manual gives a maximum lift height of 10 m at a safety factor of 8 and 8 m at a safety factor of 10 for a single hanging beam, while the configuration sheet lists a maximum rigging height of 8 m — confirm which figure governs the project and have the structural engineer sign off the corner load path.
- Service method: confirm front service is possible before the corner is enclosed, because rear access at a corner is frequently blocked by the building structure.
Frequently asked questions
Can a 90° corner be made from standard LED cabinets?
Yes, as a butt joint, but one face loses at least the cabinet depth at the vertex — 83 mm on a UR Pro 500 × 500 mm indoor cabinet, 91.51 mm on an RK Pro P6.6 cabinet. The documented fix is a factory corner part — a 45°-cut cabinet on UR Pro and RK Pro, or a 90° splicing design on RK, IW, TSL and AM. A site-fabricated corner post is the fallback only where the chosen series has no factory right-angle option for that cabinet size, and it is difficult to repeat across multiple sites.
Does a corner change the pixel pitch or the resolution?
No. Pitch is fixed by the module, and each face keeps its own rectangular pixel grid. A 1,500 × 2,000 mm UR Pro P2.604 face is 576 × 768 px whether or not it meets a corner. The corner only changes where the pixel grid terminates.
Is there a documented 90° corner cabinet for RK, RK Pro, IW, TSL or AM?
Every major series in this source pack documents a right-angle option, but they solve it three different ways: a 45°-cut cabinet (UR Pro “45° corner cabinet”; RK Pro “cabinets can be cut to 45° angles for seamless corner fitting”), a 90° splicing design (IW “dual-purpose 90° splicing”; TSL “90° right angle spliced”; AM “90° external right-angle”, with curve splicing adjustable at ±15°; RK “right angle splicing”), and a corner connecting piece (AS “Corner Screen Installation (90°)” with a corner connecting piece). UR also documents right-angle and convex-curve configurations. What differs is repeatability and the angle range, not whether a corner is possible.
How many corner cabinets does a 3 m tall corner need?
Twelve — 6 rows of 500 mm on each of the two faces, one corner cabinet per face per row. Corner cabinets are a unique part, so the spare-parts allowance should be calculated on the corner cabinet count, not on the total cabinet count.
Planning a corner for a retail rollout? The UR Pro Series is the platform with a documented 45° corner procedure; the retail LED display guide covers the rest of the store specification, and the 500 × 500 mm cabinet count method helps you fix the grid before you draw the corner.
Send Uniview LED(优景观复) your corner dimensions
Before installation, run the corner design through the LED wall installation checklist for structure, power and data sign-off.
Three Questions to Answer Before Specifying a Corner LED Cabinet
- Is the corner a convex outside corner on the shopper’s walking path, or a concave reveal that only staff will see?
- What are the two face widths and the total height in millimeters, and do those dimensions land on a 500 mm module grid?
- Who will service the display, and is there usable rear access behind the corner at working height?